Optics ▶ Mounting Tools - Scopes ▶ Crosshair Levelers ▶

Wheeler Engineering Level-Level-Level Scope Crosshair Leveling Tool

Product #: 529349 Wheeler Engineering #: 113088 UPC #: 661120130888

Loading image...

Enlarge Zoom in

$14.99

$20.49

Save $5.50 (26%)

Sale expires 05/31/2013

Status:

Available

Ready to ship

Email this Page to a Friend

Quantity:

Please Sign In to use this feature.

Substitute Products

Others Bought

Product Information

The simplest, most accurate scope leveling system ever devised to level your scope as you mount it on your rifle. The magnetic base in the rifle level bridges the bolt raceway, allowing you to position your rifle almost perfectly level. Then level the scope, tighten the rings and the job is done. Works with practically any bolt-action rifle. Set includes two levels.

Application Charts & Information

Was this information helpful? Yes No

This Information was not helpful because:

Know someone who may like this? Email this Page to a Friend

Customer Reviews

.prPaPagination,.pr-pagination-bottom,.prPaFooter,.pr-pagination-top,.pr-review-tools,p.pr-review-faceoff-review{display:none} .pr-review-faceoff .pr-review-faceoff-review-full{display:block} .prReviewAuthorProfileLnk{color:#000;font-weight:bold;cursor:text} .prReviewAuthorProfileLnk:hover{text-decoration:none}

Attention

JavaScript is disabled. You must enable JavaScript in order to interact with reviews or write your own.

REVIEW SUMMARY

by PowerReviews

Wheeler Engineering Level-Level-Level Scope Crosshair Leveling Tool

2.8

(based on 145 reviews)

75%

of respondents would recommend this to a friend.

Most Helpful Positive Review

Product works great on ...

Product works great on Remingtons, takes a little patience with Winchesters and Weatherbys. Magnets are a little weak but you must remember they don't work on stainless, aluminum or chro-molly. Tip - place levels on flat surface noting bubble relationship to cursor lines. Turn the scope base level 180 degrees and note the position. Mark with an arrow the direction on the scope base level that best matches the bubble position of the breach level. This should give you the most accurate alignment for your set of levels.

Most Helpful Negative Review

The idea behind the ...

The idea behind the product is good, but the product quality is almost junk. The magnet was weak, but usable even on a LVSF Remington(stainless). I checked both scope levels with a...Read complete review

The idea behind the product is good, but the product quality is almost junk. The magnet was weak, but usable even on a LVSF Remington(stainless). I checked both scope levels with a quality four foot level and two Starrett machine levels, the scope level bubbles were way off, and different from each other! That alone would make it almost impossible to get satisfactory results from the product. Maybe I just got a bad set, but I'm returning mine for a refund!

Reviewed by 145 customers

Sort by

Displaying reviews 1-10

Previous | Next »

12/6/2012

4.0

I would recommend tis product.

By Ken Blatny

from Omaha, Ne.

Comments about Wheeler Engineering Level-Level-Level Scope Crosshair Leveling Tool:

Works good except some scopes are off with or with out the cap on. Best is to draw a orizontal
line with a level at 25 yards or more and check
for level since the elevation cap and cross hair
can be off to the receiver level.

11/30/2012

5.0

So good I bought another, and another...

By Kendall

from Central, IL

Comments about Wheeler Engineering Level-Level-Level Scope Crosshair Leveling Tool:

My first turbo 1200 was a garage sale find. I used it for years. I finally decided it was time to get another to speed things up. WOW! the new one was much faster. I didn't realize how slow the old one had gotten. I was a little aprehensive about the noise some reviews spoke of. Mine is much quieter than the older model. I would like to have a power switch, but I simply used a power strip with a switch. I am very happy with the quality. If these new tumblers last as long as the old model (it's still working fine just slower) I will be very happy.

11/30/2012

5.0

Must have...

By Kendall

from Central, IL

Comments about Wheeler Engineering Level-Level-Level Scope Crosshair Leveling Tool:

If you mount many scopes, you should have this tool. I mounted many many scopes without it. I would think I had it as square as could be. She would tell me it was leaning. I would set it where she thought it should be. I thought it was crooked. I got this tool and now it looks better to both of us. I won't tighten down scope rings without using this to check now. Very easy to use and takes all the guesswork out. I should have bought this years ago.

11/28/2012

1.0

JUNK!!!

By Matt

from Sunbury, OH

Comments about Wheeler Engineering Level-Level-Level Scope Crosshair Leveling Tool:

Don't waste your money. These things are complete junk. I sat them side by side and the bubbles did not read the same when sitting right next to each other on a flat desk top.

7/7/2012

2.0

Work great on rem 700 but ...

By Jared

from Carl Junction, MO

Comments about Wheeler Engineering Level-Level-Level Scope Crosshair Leveling Tool:

Work great on rem 700 but hard to use on other guns. Most of my scopes are domed turrets and don't have a flat turret to get level.

6/23/2012

(1 of 1 customers found this review helpful)

3.0

This product (like the ...

By Kevin

from Atwater, CA

Comments about Wheeler Engineering Level-Level-Level Scope Crosshair Leveling Tool:

This product (like the Weaver one) rely on several assumptions. One is that you have flat spots on the gun that's perpendicular to the bore and on your scope that's perpendicular to the crosshairs. If you have both, then great. Having worked at a construction site I know that a level is more accurate the longer it is assuming accurate placement of the bubble. These levels are really short so there's a lot that could go wrong with the installation. I used the product but wasn't satisfied with the results so I put my handgun in a bench vise and leveled the gun with different more accurate levels and then looked through the scope onto my garage door panels (which I previously checked to make sure that they were level). I then had a spot on mounting of my scope. If you find a Segway Reticle Leveler, use that! They're cheap, but hard to find, and do the job in a tenth of the time more accurately than any level tool could get.

6/4/2012

3.0

I used this to mount ...

By Nick

from Corona, CA

Comments about Wheeler Engineering Level-Level-Level Scope Crosshair Leveling Tool:

I used this to mount scopes on 3 rifles. I have a Nikon on an AR10 that worked out fine, I just had to double side tape the base level to the top of the receiver. I mounted a VX-1 to a T/C Venture and Leupolds have nothing magnetic for the top bubble to stick to, so I had to hold it on my hand and it proved to be a little troublesome. Although the base bubble would not fit in the bolt window, there is a flat milled on top of the receiver that worked just fine. The worse problem I had was mounting a VX-3 on my Kimber 84l. There are no flats on the receiver and the base magnet would not fit into the bolt area. I had to butcher the base bubble to get it to fit inside the action with a razorblade, so it is basically useless for any other rifle now. The elevation adjustment on the VX-3 is domed and non-magnetic so I had to go off the caps and hope it is square to the crosshair. It got it close but still needed more refinement. This seems to be designed for a 700 action with scopes other than Leupold, so if thats what you have this product will probably work out great for you. With the rifles I have it was hit and miss.

6/1/2012

4.0

It did as advertised, ...

By Carlos

from San Diego, CA

Comments about Wheeler Engineering Level-Level-Level Scope Crosshair Leveling Tool:

It did as advertised, just keep them in a cool place or they melt off their base!

5/23/2012

(0 of 1 customers found this review helpful)

5.0

I would like to know if ...

By Tammy

from Roanoke, VA

Comments about Wheeler Engineering Level-Level-Level Scope Crosshair Leveling Tool:

I would like to know if this sight will work on a K98 Mauserand need to know 100 percent if it will work and what adjustments will I need and tools to make it workand what about the other set of sights what would you recommend for my other sights to go hand in hand with these open sightsI would also like to mount a short sideways scope with laser and flash lightwhat would I need to mount the sights to the left side as not to interfere with the loading of ammocan anyone help me out herealleycat_entertainment@hotmailcomplease send me links to try and help me with this projectthis website has helped me in the past some very smart people on it and very helpful people.Tammy

5/22/2012

1.0

Absolutely useless on my ...

By Harv

from Statesville, NC

Comments about Wheeler Engineering Level-Level-Level Scope Crosshair Leveling Tool:

Absolutely useless on my Savage .17 HMR Bolt Action. Does not bridge the bolt raceway as advertised. Could not find any way to use the bottom level on a Savage Model 93R .17HMR

Displaying reviews 1-10

Previous | Next »

The statements and opinions expressed within Customer Reviews reflect each author's personal perspective and do not imply endorsement by MidwayUSA, its Employees or any other organization. Customers should in no way infer that MidwayUSA has validated review information as safe, accurate or appropriate.

NOTE: Prices, specifications and availability are subject to change without notice.
We reserve the right to correct typographic, photographic and/or descriptive errors.

Wheeler Engineering Level-Level-Level Scope Crosshair Leveling Tool

Suggested Products

Substitute Products

Others Bought

Product Information

This Information was not helpful because:

Customer Reviews

Recently Added

Suggested Products