You are here: Homepage > Gunsmithing > Tools for AR-15 > 

AR-Stoner Multi-Tool AR-15 Steel

Product #: 271183
| Manufacturer #: 1570-4
Status: Available
   Should Ship Next Business Day
Quantity

A must-have for every AR-15 owner, this tool allows for most any AR project, from installing handguards and buttstocks to detailed inspection and disassembly. Especially recommended for installing and removing free-float tubes.

Application Charts & Information

Overall Rating:
2.6 out of 5
Used this Product?Rate It
5 stars
marc t of aberdeen, nc
Date posted: 6/1/2007
very capable tool. can easily be used for a multitude of applications on AR 15. WILL NOT bend like the cheapies do
Was this review helpful?
Yes |
27 found it helpful |
0 did not
4 stars
Robert Szelinski of New Caney , TX
Date posted: 1/8/2009
Well built tool and will hold up to any AR-15 application. The finish hasn't been a problem one bit. Comes in very handy and is an good buy for any AR-15 owner.
Was this review helpful?
Yes |
11 found it helpful |
0 did not
4 stars
Alfred Amrhein of San Antonio, TX
Date posted: 1/3/2009
This is one sturdy tool, solid will not bend, heavy duty all I can say about the slippage issue is try a little paint remover on the tool when the paint goes away so does the slippage, just keep a light coat of oil on the areas where you stripped the paint.
Was this review helpful?
Yes |
15 found it helpful |
0 did not
4 stars
Cord Ogle of fullerton, CA
Date posted: 6/16/2006
This tool worked great for my AR build. The only reason I did not give it five stars was the notch for the Lower Receiver Extension was a little large and caught just the corners of the extension. Otherwise, this is a great buy for the price.
Was this review helpful?
Yes |
66 found it helpful |
1 did not
3 stars
Gary N of Natchez, MS
Date posted: 9/10/2008
This tool is made from good material (I doubt you will bend it). I can't rate it any higher than three stars because the fit could be better. For general maintenance it's OK but if I was working on a new rifle that I didn't want to take a chance at scratching I would look for something better. This tool will work but you have to be careful and take your time so it doesn't slip and scratch the rifles finish. Overall I rate it OK.
Was this review helpful?
Yes |
19 found it helpful |
0 did not
3 stars
Deke Knight of Titusville, FL
Date posted: 4/2/2009
The tool worked fine after getting all the coating off the mating surfaces. I'd recommend the mfg. not coat the tool but spray it with CLR or a light oil, put it a zip lock bag and ship it. The coating creates an out of tolerance condition that does not allow the tool to fit properly.
Was this review helpful?
Yes |
4 found it helpful |
0 did not
2 stars
J Cano of Clifton, TX
Date posted: 12/30/2008
I had to modify the tool by doing some grinding to the spanner pegs that are supposed to fit in the slots for the buttstock extension nut. There is too much powder coating on the whole tool therefore making it difficult to make it fit. The only reason I didn't give it one star was that it will not bend which is good.
Was this review helpful?
Yes |
13 found it helpful |
0 did not
1 stars
R Curtiss of Chesterfield, VA
Date posted: 1/17/2007
Slippery finish allows tool to jump out of notches on both barrel nuts and tube nuts causing damage. A bad tool to have around. There are much better tools for barrel and extension tube work.
Was this review helpful?
Yes |
81 found it helpful |
10 did not
1 stars
Les Voorhies of Faribault, MN
Date posted: 11/14/2009
I had the same problem as the previous 2 reviewers had. It's very hard to get the proper torque and gas tube alignment with this tool. I marred one barrel nut badly trying to get it off and busted my knuckles trying to install another.
Was this review helpful?
Yes |
0 found it helpful |
0 did not
1 stars
Monte Barnes of Gage, OK
Date posted: 2/19/2008
I agree with previous comments. This tool slips off of the barrel nuts and causes damage. I cannot recommend it. The price was good but not at the expense of rifle damage.
Was this review helpful?
Yes |
38 found it helpful |
0 did not
1 stars
JOHN S of LYNCHBURG, VA
Date posted: 9/18/2009
The finish on this tool is slippery and soft making it difficult to adequately tighten barrel nuts and castle nuts on buffer tubes for collapsible stocks. I have damaged several very expensive rifles using this multi-tool and I would strongly discourage people from purchasing this product. On the other hand Midway offers some great alternatives.
Was this review helpful?
Yes |
0 found it helpful |
0 did not
Have a question? Visit GunTec Dictionary Need a gunsmith? Visit Gunsmith Locator
NOTE: Prices, specifications and availability are subject to change without notice.
We reserve the right to correct typographic, photographic and/or descriptive errors.
WEBSRVR3