Lyman Power Chamfer and Deburring Kit

Product #: 331699
| Manufacturer #: 7777758
Status: Available
   Should Ship Today
Quantity

Take the drudgery out of the case preparation process with the Lyman Power Deburring Kit. High torque rechargeable power driver turns at the perfect speed for performing deburring operations in seconds. Kit includes all the essential case prep accessories, including large and small primer pocket reamers and cleaners, case neck brushes, inside and outside deburring tools, standard and Phillips driver bits and recharger. Accessories simply pop in and out of the driver, with the included hex adapters.

Technical Information

Features:

  • Kit is a high torque rechargeable power driver.
    Includes:
  • Large and small primer pocket reamers and cleaners, case neck
  • Brushes, and inside/outside deburring tools, with the included hex adapters.
    Notes:
  • Accessories snap into the driver.
  • Also includes standard and phillips driver bits and power adapter.
  • Powered by two 1.2 volt nickel rechargeable batteries or the power adapter.

    • Application Charts & Information

    Overall Rating:
    3.6 out of 5
    Used this Product?Rate It
    5 stars
    Bill Heitzenrater of DuBois, PA
    Date posted: 6/26/2003
    The tool cut my time deburring and cleaning primer pockets by more than 50%. I have only used it twice and find the cutting edges excellent. I would suggest that some sort of cradle be added to the package. I found the tool easier to use by laying it on the bench and manipulating the cases. However, being round, it has a tendency to slide.
    Was this review helpful?
    Yes |
    10 found it helpful |
    0 did not
    5 stars
    Arthur Hicken of Upland, CA
    Date posted: 9/8/2004
    This tool is really great. It does an amazing job of chamfering. You can even tell when you brass is brittle by the way it bites into it. I ran through 400 pieces of brass in very little time.
    Was this review helpful?
    Yes |
    3 found it helpful |
    0 did not
    5 stars
    Morgan Conrad of Youngstwon, OH
    Date posted: 6/26/2003
    I really like the Lyman Power deburring tool, it sure speeds up the process of reloading brass and saves my wrist along with it, plus if I need to I can also use it as a hand drill for smaller jobs. Thank you lyman for a very useful product.
    Was this review helpful?
    Yes |
    8 found it helpful |
    2 did not
    5 stars
    Howard Wentz of Winamac, IN
    Date posted: 6/26/2003
    This tool lets you process large numbers of cases in a short time & no sore fingers
    Was this review helpful?
    Yes |
    7 found it helpful |
    1 did not
    4 stars
    Lou DeAngelis of Pittsburgh, PA
    Date posted: 6/29/2003
    Works great, I trim between 500 and a 1000 at a time it really speeds up the process, plus my hand does not go numb.
    Was this review helpful?
    Yes |
    14 found it helpful |
    1 did not
    3 stars
    William Wheeler of Tampa, FL
    Date posted: 11/28/2007
    Cheapo made in China construction, but it works great, 4 stars, for cleaning primer pockets. If RCBS would get their act together and make some decent primer pocket cleaning tools for their Trim Mate case prep center that would be far better. Although pricey for what it is, this one works good and you'd be surprised how much residue it easily removes.
    Was this review helpful?
    Yes |
    5 found it helpful |
    0 did not
    1 stars
    Jeffrey L of West Allis, Wi
    Date posted: 1/4/2010
    The unit itself is just a waste of time and money. It is slow and doesn't charge well. The bits that come with it are good to have. I just use them with my cordless drill now. The drill has more control and the battery charges way faster.
    Was this review helpful?
    Yes |
    1 found it helpful |
    0 did not
    1 stars
    Larry Leesch of San Antonio, Tx
    Date posted: 9/19/2009
    I'd rank this right there with a useless paperweight. I will speed up the process and it does work....sometimes. Leave it for a few weeks and then attempt to use it and find the battery dead. It takes DAYS for it to charge up. A much better design would have the unit running off of the charger alone, something Lyman chose not to build into this expensive junk. Unless you intend to KEEP it on the charger and waste loads of electricity, find something other than this unit.
    Was this review helpful?
    Yes |
    0 found it helpful |
    2 did not
    Have a question? Visit GunTec Dictionary Need a gunsmith? Visit Gunsmith Locator
    NOTE: Prices, specifications and availability are subject to change without notice.
    We reserve the right to correct typographic, photographic and/or descriptive errors.
    WEBSRVR5