Lyman Chamfer and Deburring Tool VLD (Very Low Drag)

Product #: 342199
| Manufacturer #: 7777789
Status: Available
   Should Ship Today
Quantity

Standard reamers chamfer with a 45 degree angle. The Lyman VLD (Very Low Drag) cuts at 22 degrees. Bullets will fit easily into the case avoiding damage from sharp case mouths. Comes with a steel reamer and ergonomic handle.

Application Charts & Information

Overall Rating:
3.7 out of 5
Used this Product?Rate It
5 stars
John Robinson of Washington, PA
Date posted: 5/11/2002
Really sharp tool that was big improvement over previous RCBS product I had. Liked it so much for what it did with coated bullets and lead that I use it exclusively now.
Was this review helpful?
Yes |
44 found it helpful |
4 did not
5 stars
F Pop of CHEYENNE, wy
Date posted: 10/10/2006
Very sharp tool. Worth its weight in gold! No shaved bullets when using this to chamfer inside of necks of cases. Especially helpful with high bc bullets.
Was this review helpful?
Yes |
7 found it helpful |
0 did not
5 stars
John Galbraith of Alachua, FL
Date posted: 6/5/2004
I purchased one of these when I started using Barnes coated bullets. Now I use it for all bullets. They seat without a hitch and I have not ruined a case since I started using this reamer.
Was this review helpful?
Yes |
22 found it helpful |
0 did not
5 stars
Greg Doherty of Framingham, MA
Date posted: 1/4/2006
Great tool that gets even better when you remove it from the wooden handle and install it on an electric screw driver - gets the job done fast with more even chamfer then you can do by hand.
Was this review helpful?
Yes |
8 found it helpful |
0 did not
5 stars
glenn notsch of phoenix, az
Date posted: 5/31/2007
Great tool! I now use this exclusivly to trim the inside of all cases. It is especially great with narrow cases like .204 Ruger, but I also use it exclusivly on 6.5x55 and 30.06-I wish I had bought this years ago. It was surprising to read that some guys said theirs arrived dull. Mine, is so sharp I have to be extra careful not to cut or stab myself. It easlily trims brass.
Was this review helpful?
Yes |
4 found it helpful |
0 did not
5 stars
Clarence Murray of Bristol, VA
Date posted: 4/23/2009
I found that this tool will cut nicely but it must be turned counter clockwise.
Was this review helpful?
Yes |
1 found it helpful |
1 did not
5 stars
ALFRED AMRHEIN of San Antonio, TX
Date posted: 8/27/2009
This tool works great I use it after I trim my rifle cases and it works like a champ. It is also great for removing the crimp on military brass for small primers, I have already done several thousand cases and it is still going strong
Was this review helpful?
Yes |
1 found it helpful |
1 did not
5 stars
Chris Walley of Waynesboro, MS
Date posted: 7/26/2007
I would be lost without this chamfer tool. Like others have said, I now use this tool for all bullets VLD or otherwise.
Was this review helpful?
Yes |
2 found it helpful |
0 did not
1 stars
John Hunt of Prescott, AZ
Date posted: 6/1/2006
I bought this first and then bought the RCBS VLD tool because this one was worthless. Reasons not to purchase this item. 1. Arrives so dull it can't chamfer any case no matter how soft the brass and it's not like you can sharpen it yourself.
Was this review helpful?
Yes |
9 found it helpful |
2 did not
1 stars
Adam Kielcz of Cincinnati, OH
Date posted: 12/30/2004
Just received it today and it's completely dull. Doesn't cut any chamfer. Waste of money.
Was this review helpful?
Yes |
40 found it helpful |
12 did not
1 stars
Steve Suhr of Franklin, WI
Date posted: 2/5/2006
Unfortunately this tool was absolutely DULL. It would not deburr even my softest, annealed case mouth. I cannot recommend this deburring tool.
Was this review helpful?
Yes |
13 found it helpful |
3 did not
1 stars
Chris Bass of Chowchilla, CA
Date posted: 11/20/2008
Well I thought I would see for myself, and yes, the tool came very dull, and is more or less useless. Does more flaring than cutting.
Was this review helpful?
Yes |
5 found it helpful |
2 did not
Have a question? Visit GunTec Dictionary Need a gunsmith? Visit Gunsmith Locator
NOTE: Prices, specifications and availability are subject to change without notice.
We reserve the right to correct typographic, photographic and/or descriptive errors.
WEBSRVR13