B-Square 31-Piece Professional Gunsmith Screwdriver Set

Product #: 429783
| Manufacturer #: T0045
Status: Available
   Should Ship Next Business Day
Quantity

The Professional Gunsmith Screwdriver Set comes complete with 26 hardened steel bits including Phillips, slotted, hex, torx and posi-drive, plus three long bits for recoil pad and see-thru mount installation, a full-featured screwdriver and a 1/4" socket drive adapter in a convenient carrying case.

Application Charts & Information

Overall Rating:
3.1 out of 5
Used this Product?Rate It
5 stars
Mike Fleischer of Wernersville, Pa
Date posted: 3/10/2003
A very good value. Works great in my range box. I use them often, I see no wear on the blades.
Was this review helpful?
Yes |
106 found it helpful |
7 did not
5 stars
Dave Breckenridge of Princeton, Mn
Date posted: 11/30/2003
I've been using this set for years and use them for everything from scope mounting to auto repair. These bits are not soft as stated by other users. This set is a phenomenal value for the price.
Was this review helpful?
Yes |
57 found it helpful |
0 did not
5 stars
Ryan Sims of Baker, LA
Date posted: 2/2/2004
Since I work at a shooting range, I use this set several times a day. The bits hold up perfectly, I have yet to have a job where the set has not stood up to my expectations.
Was this review helpful?
Yes |
43 found it helpful |
0 did not
5 stars
Chris Martin of North East, md
Date posted: 6/25/2008
Great value. I used this kit to mount scopes and rings, shotgun saddle mounts and a few other gun parts and accessories and this kit met all of my demands. I would definitely recommend.
Was this review helpful?
Yes |
3 found it helpful |
0 did not
5 stars
Mike Mackesey of East Troy, WI
Date posted: 8/10/2009
This is a fine product! I expect there are far better screwdriver sets available, but not in the price range of this one. Keeping in mind that a single decent screwdriver will cost $6.00 to $10.00, this is a steal.
Was this review helpful?
Yes |
2 found it helpful |
0 did not
4 stars
Dave Thompson of Bainbridge Island, WA
Date posted: 7/19/2005
Works well for most range jobs. The smallest flat blade bit twisted the first time I used it on a tight screw. I wish the kit included smaller flat blade bits for adjusting sights.
Was this review helpful?
Yes |
5 found it helpful |
1 did not
4 stars
Albert Anderson of Houston, TX
Date posted: 10/4/2005
Good set for the money; however, do not assume because it is a gunsmith screwdriver set, that it will have bits which are a good fit for your particular gun's screwheads. I have a .444 Marlin, and the smallest bit is a very loose fit (too thin) in the scope set screws. This set should have more flathead bits than it does, particularly in the smallest bits range. If you want a set for your gun, either go for an expensive complete gunsmith set, or purchase a gun specific set.
Was this review helpful?
Yes |
13 found it helpful |
1 did not
4 stars
Gerald Minor of Albuquerque, NM
Date posted: 2/25/2005
This set is a very good value for the cost. I purchased this set to keep in my range bag, but the day it came I needed to replace the ejector on a Marlin 39A. Very thin slots, very tight, but the B-Square set had a bit that fit perfectly, and removed these screws without problem. I was impressed. Maybe the best set in the world, but it should serve the needs of the average gun owner very well.
Was this review helpful?
Yes |
16 found it helpful |
0 did not
4 stars
TC Hailey of Coarsegold, CA
Date posted: 11/6/2001
All the blades fit tightly and they do not seem to slip out of the screws like some other brands do.
Was this review helpful?
Yes |
76 found it helpful |
1 did not
4 stars
Randy Perry of Shelby, NE
Date posted: 5/23/2004
Good Gunsmith Screwdriver Set for the money. Can't complain to loudly as I've torqued the tips fairly hard thinking they would give and break, but they have stood up and taken the test. Not a bad value. The case is a nice unit to take to the field or throw in your toolbox.
Was this review helpful?
Yes |
77 found it helpful |
1 did not
4 stars
Al Schweitzer of Kalamazoo, MI
Date posted: 8/26/2007
Not a bad little set to have around. I am not a power gunsmith yet need a half way decent set of gunsmithing screwdrivers and bits to keep handy. This kit does the trick just fine.
Was this review helpful?
Yes |
0 found it helpful |
2 did not
4 stars
Greg Rosenberger of Louisville, KY
Date posted: 8/19/2006
I was pleased with the performance and fit of the various tips. I had been putting off some minor repairs due to lack of tools. This kit covered all the bases; I am completely satisfied.
Was this review helpful?
Yes |
1 found it helpful |
2 did not
3 stars
L. McGraw of St. Albans, VT
Date posted: 1/24/2002
I must have a hundred gunsmith screwdrivers, including just about every brand available. These work as well as most. Fit and finish could be better but, they are just about perfect for the odd job at the range.
Was this review helpful?
Yes |
40 found it helpful |
1 did not
3 stars
Philip Schreiner of Avon Lake, OH
Date posted: 8/31/2006
Good driver set for range / field use. Not the best for serious work. These bits tend to yield to any stubborn fasteners. For the price however, this is to be expected.
Was this review helpful?
Yes |
3 found it helpful |
2 did not
2 stars
John Cannon of Newton Grove, NC
Date posted: 2/26/2004
At first, this appeared to be a wonderful set for the shop. However, while installing the 3rd scope, the torx bit stripped completely. The bits are VERY soft and will not take everyday use. Caution should be exercised if you are going to use these for anything other than MINOR repairs/projects. I liked the molded plastic case. I just wish they could have made the bits more suited for professional applications.
Was this review helpful?
Yes |
28 found it helpful |
0 did not
2 stars
Greg Nowark of Binghamton, NY
Date posted: 1/21/2002
Fit screws well (no marks left), but bits were too soft to remove factory screws. Twisted ends off from several straight bits.
Was this review helpful?
Yes |
59 found it helpful |
2 did not
2 stars
CRAIG MERHOFF of KLAMATH FALLS, OR
Date posted: 10/5/2007
Great handle, but several of the bits that I've used are too soft and have twisted or in the case of one Torx bit, broken off while tightening scope ring screws. I can't recommend this set for anyone who wants to get screws tight enough to keep a scope from moving. I do have very strong hands, but these bits are too soft.
Was this review helpful?
Yes |
0 found it helpful |
0 did not
2 stars
Seth Crawford of Baton Rouge, la
Date posted: 3/29/2006
CONS: The bits are too soft. Maybe I got a set they forgot to heat treat but I have had two bits fail. One bent, the other outright broke off. PRO: the bit selection and sizes are pretty good. Wish the magnetic part of the driver was removable.
Was this review helpful?
Yes |
4 found it helpful |
1 did not
2 stars
Terry Lovell of Huntsville, AL
Date posted: 12/5/2004
When using the small flat head blade for the first time to remove some very tight muzzle tap screws, the edge of the blade twisted off. What can you expect for $13.
Was this review helpful?
Yes |
4 found it helpful |
2 did not
2 stars
Jonathan Bigony of Bowie, MD
Date posted: 10/4/2006
The bits are very soft, twist easily and don't really fit well. However for the price, I guess they're okay in a pinch.
Was this review helpful?
Yes |
2 found it helpful |
3 did not
1 stars
Jeffrey Lippert of Lincolnwood, IL
Date posted: 6/14/2006
First time I used a screwdriver bit it broke. No variation in bit thickness which makes for a poor fit in the screws.
Was this review helpful?
Yes |
7 found it helpful |
0 did not
1 stars
Frank Walker of Sylvester, GA
Date posted: 7/11/2004
This product leaves a lot to be desired in durability. I used this product for the first time to change out a scope mount. I broke one tip and bent two others removing the old mount. The set is now collecting dust on a shelf.
Was this review helpful?
Yes |
28 found it helpful |
2 did not
1 stars
Glenn Travis of Lake Jackson, TX
Date posted: 6/26/2007
The locking tab was unattached to the lid. It did not even come out of the plastic shipping container. This flaw or lack of quality assurance does make me question the rest of the product and in particular when I read the reports expressing the concerns of other reviewers. The bits did serve my needs, however, I did not need to use much torque when I used them at the gun club this weekend. Thank you.
Was this review helpful?
Yes |
2 found it helpful |
1 did not
1 stars
george smith of rochester, ny
Date posted: 7/8/2007
Junk! The screwdriver handle body cracked after only a few hours of use, making the threaded plug fall out. $20 wasted. I expected better from this company.
Was this review helpful?
Yes |
5 found it helpful |
1 did not
Have a question? Visit GunTec Dictionary Need a gunsmith? Visit Gunsmith Locator
NOTE: Prices, specifications and availability are subject to change without notice.
We reserve the right to correct typographic, photographic and/or descriptive errors.
WEBSRVR5