Power Custom 1-Piece Weaver-Style Base Ruger 10/22 Matte

Product #: 531713Manufacturer #: 10/22 BASE BLACK
Status:
Should ship today
$16.99
 

The Power Custom Weaver-style Base mounts to the receiver of your rifle with no gunsmithing required. Much better than using tip-off rings if you're mounting a target-style scope. Does not fit Ruger 10/22 Magnum.

Technical Information

Material: Aluminum

Style: Weaver

Fits:

  • Ruger 10/22
    Notes:
  • Attaches to the factory pre-drilled and tapped holes in the 10/22 receiver.
  • Measures 4.875"x.875"x.350"
  • Mounting hardware included.

    • Application Charts & Information

    Overall Rating: 5 stars
    Used this Product?Rate It
    5 stars
    Joe Self of Columbia, TN
    Date posted: 1/26/2007
    This mount is excellent. It's very well made and the finish is quite tough. However, this mount is too thick to use the stock iron sights while it is attached.
    Was this review helpful?
    Yes |
    20 found it helpful |
    1 did not
    5 stars
    Pete Stephenson of Tucson, AZ
    Date posted: 3/5/2007
    Great rail. Comes with hex-head screws and a L-shaped hex wrench to screw them in. No machining marks or other blemishes; you couldn't tell this rail from a factory part. The many notches allow the use of various Weaver mounts for red-dot sights and scope rings. Weaver mounts are much more common than the little rail that comes with the 10/22, so this has made things a lot easier. For less than $20, you can't go wrong with this rail. It has more notches than the Leupold rail, allowing a bit more flexibility.
    Was this review helpful?
    Yes |
    24 found it helpful |
    0 did not
    5 stars
    Barry Sanders of Jefferson city, MO
    Date posted: 8/5/2007
    Very nice base. Much better than factory. Perfect fit. Will fit a lot of different scopes. Screws and wrench are supplied.
    Was this review helpful?
    Yes |
    7 found it helpful |
    0 did not
    5 stars
    Brad Tullos of St. Francis, AR
    Date posted: 1/20/2005
    Very good product. Fit the reciever perfectly and the multiple grooves allow a lot of flexibilty for mounting different types of optics.
    Was this review helpful?
    Yes |
    48 found it helpful |
    1 did not
    5 stars
    Steven R. Wolfson of Dallas, TX
    Date posted: 2/18/2005
    Fit right on my old model 10/22 in a jiffy. I mounted a Tasco ProPoint 3 Plus (from Midway) and the whole set up was perfect, and quick. 15 minutes, tops, to install everything. Thanks Midway.
    Was this review helpful?
    Yes |
    24 found it helpful |
    0 did not
    5 stars
    Eric Sebertsen of Mystic, CT
    Date posted: 6/19/2005
    Very good product. The mount and included socket head screws are very well finished. This mount combined with Leupold vertical split rings cost less. Very slick and sturdy.
    Was this review helpful?
    Yes |
    30 found it helpful |
    0 did not
    5 stars
    Dick Milburn of Taylorsville, CA
    Date posted: 11/1/2008
    I liked the extra height of the mount. It fit perfectly and looks good once the rifle is all togeather. Thanks for making a great product.
    Was this review helpful?
    Yes |
    1 found it helpful |
    0 did not
    5 stars
    RICHARD ACKERMAN of WILMINGTON, DE
    Date posted: 6/18/2009
    Excellent part, included everything needed to install on my rifle except the Loctite. Fit perfectly, & made a great improvement in accuracy with Millett rings & a Weaver KT 15 scope
    Was this review helpful?
    Yes |
    1 found it helpful |
    0 did not
    5 stars
    B of Edmond, OK
    Date posted: 7/15/2010
    I am very happy with this mount and it fit perfectly on my 20+ yr. old Ruger 10/22. The extra height provided by this mount gave me a better sight position than standard Weaver mounts normally seen for the 10/22.
    Was this review helpful?
    Yes |
    0 found it helpful |
    0 did not
    5 stars
    Mark F of Abilene, TX
    Date posted: 6/26/2008
    Much better than the factory mount. Allows use of normal size Weaver rings. It is pretty thick so iron sights won't work with this installed.
    Was this review helpful?
    Yes |
    8 found it helpful |
    0 did not
    5 stars
    Nicholas Nelson of Glenwood Springs, CO
    Date posted: 8/17/2008
    I got this particular mount due to its sturdy build. It is what I wanted. Very rigid. The holes lined up perfect, no fitting whatsoever was needed.
    Was this review helpful?
    Yes |
    7 found it helpful |
    0 did not
    5 stars
    Michael A. of San Gabriel, CA
    Date posted: 8/29/2008
    As others have said, fits perfectly. All hardware and an allen key are supplied. Nice price as well.
    Was this review helpful?
    Yes |
    1 found it helpful |
    0 did not
    Have a question? Visit GunTec Dictionary Need a gunsmith? Visit Gunsmith Locator
    NOTE: Prices, specifications and availability are subject to change without notice.
    We reserve the right to correct typographic, photographic and/or descriptive errors.
    WEBSRVR6