Williams WGRS-336 Guide Receiver Peep Sight Set Marlin Lever Actions with Fire Sight Front Sight Aluminum Black

Product #: 945296
| Manufacturer #: 70018
   Date Expected In-Stock: 3/15/2010
Quantity

An economical set that includes the compact low profile Williams Guide Receiver Sight and the appropriate height front sight. The Guide Receiver Sight features simple, positive screw-lock windage and elevation adjustments. In most cases the sight utilizes the existing scope mounting screw holes or dovetail on top of the receiver for installation. Red Fire Sight included.

Technical Information

Material: Light, Rustproof Aluminum Alloy

Adjustments:

  • Fully Adjustable for Windage and Elevation

    Gunsmithing Required: No, however front sight will likely require fitting

    • Application Charts & Information

    Overall Rating:
    2.7 out of 5
    Used this Product?Rate It
    5 stars
    Charles Sala of Pittsburgh, PA
    Date posted: 3/22/2008
    This was just what I was looking for. A well made low profile simple sight. I put it on an 1894. Sight was made for the 336, it does not fit well when installed on the 1894. When using the factory taps on an 1894, the sight overhangs the rear of the gun frame. I could have had a forward hole tapped in the gun but did not want to modify the "original" gun. I used a dremmel to drill the back of the sight to "fix" the problem. I drilled a receiver hole over the rear tap plug. Put some locktite on the plug threads and let it sit a turn or two high. Then I placed the sight over this "pin" I just made and secured the sight to the gun with one screw. Very tight, very good looking and no modification to the gun. Adjusting this little sight is not convenient like other peeps but this is a trade between the big bulk of those sights and this trim looking sight. I never adjust my sight anyway. I shoot it in for the bullet and charge I am using and hold high or low. I can't see past 100 yards and the adjustment under 100 yards is negligible anyway.
    Was this review helpful?
    Yes |
    11 found it helpful |
    3 did not
    4 stars
    mike caves of ridgewood , ny
    Date posted: 5/13/2007
    I use them as back up sights for Marlin 336, which has a scout scope system. I have no problems hitting the mark at 100 yards with them and yes they are a little hard to adjust, but they work well.
    Was this review helpful?
    Yes |
    12 found it helpful |
    0 did not
    2 stars
    Tim Copeland of Clackamas, Or
    Date posted: 7/19/2003
    Very cheaply made sight. Hard to adjust. Front sight sit's awkwardly high, and the base is made of soft aluminum. So if bumped it will no doubt bend or fall off. I am going to back to the factory sights.
    Was this review helpful?
    Yes |
    80 found it helpful |
    2 did not
    2 stars
    John Doe of Geeksville, NY
    Date posted: 8/9/2003
    The rear sight is hard to adjust since locking screws are inconveniently placed. You need to screw off the aperture every time you need to adjust windage. Not really a big deal, but annoying nevertheless. The front bead and the riser block are not the conventional press-in design. Instead, they are held in place by miniature hex screws. Plus: it is easy to install. Minus: the whole front sight is not sturdy at all and tends to get shaken loose by recoil after a dozen shots, no matter how much I tried to tighten the screws. Also, it sits way too high, at least on my gun (Marlin 1894, .44 mag, 20" brl).
    Was this review helpful?
    Yes |
    139 found it helpful |
    2 did not
    2 stars
    Robert Lefebvre of Green Bay, WI
    Date posted: 10/21/2009
    After installing on my 1895, I found that the front sight was too low. So, another $30 directly to the manufacturer and it is better - not perfect, but better.
    Was this review helpful?
    Yes |
    3 found it helpful |
    0 did not
    2 stars
    Tim singer of Newgloucester, Me
    Date posted: 4/29/2008
    Bought one for my 444ss just barely able to sight it in front sight too short still shooting high. I guess I'll have to buy a taller front sight. So I guess you have to take your chances when you buy this set.
    Was this review helpful?
    Yes |
    7 found it helpful |
    1 did not
    2 stars
    Robert Bright of Petersburg, IN
    Date posted: 9/14/2007
    I bought this sight for an early Marlin Mod 1894 .44 Mag. Mounted in the rear scope mount holes the sight hung out past the back of the receiver. It obstructed access to the hammer. Even at the lowest setting it would need a much higher front sight than the one supplied. My rifle is drilled for a side mount peep sight so I returned this sight and ordered a Williams 5D94/39 receiver sight for a pre 2001 Mod 1894. When I get it I will review it. It is well made for the price, but on a Marlin you will not be able to sight it in.
    Was this review helpful?
    Yes |
    12 found it helpful |
    4 did not
    Have a question? Visit GunTec Dictionary Need a gunsmith? Visit Gunsmith Locator
    NOTE: Prices, specifications and availability are subject to change without notice.
    We reserve the right to correct typographic, photographic and/or descriptive errors.
    WEBSRVR13