You are here: Homepage > Hunting > Eye & Ear Protection > Ear Protection > Ear Plugs > 

Radians Do-It-Yourself Custom Molded Ear Plug Kit (NRR26 dB) Silicone Blue

Product #: 347115Manufacturer #: CEP001-B
Status:
Should ship today
$11.99$8.99Save $3.00
Sale expires 8/31/2010

  • Simple, easy to follow instructions
  • Safe, non-toxic and hypo-allergenic silicon
  • Long lasting and washable
  • Cures to a soft, permanent, custom fit

    Notes: These kits come with instructions, however the instructions are also included here for review prior to purchase.


    Follow the following instructions COMPLETELY to avoid compromising the fit you achieve with this product.

    Your Ear Plug Kit was shipped with canisters of colored (red, blue, green, orange, light gray or natural) and white silicone that must be mixed according to the following instructions to properly mold to the shape of your ear.

    Step 1:
  • Clean your ear and wash your hands thoroughly. Have a mirror (or willing assistant) ready before beginning.

    Step 2:
  • Gently remove the colored (red, blue, green, orange, light gray or natural) material from the container and divide into two equal portions. Store the second portion in the same container; it will be used for your other ear. Repeat for the white material. Keep the colored (red, blue, green, orange, light gray or natural) and white materials separated until ready to begin the molding process, since mixing the two will start the curing process.

    Step 3:
  • Knead together the colored (red, blue, green, orange, light gray or natural) and white portions for one ear until thoroughly mixed (about 30 seconds) and roll mixture into a uniform ball. This begins the curing process. Immediately proceed to steps 4-5.

    Step 4:
  • Place the mixture in your ear and gently apply light pressure so the material forms a cast and contours to the ear. Once a uniform, consistent form is achieved, let cure for a minimum of 15 minutes in the ear.

    Step 5:
  • Any excess material not needed to form mold can be pinched off before totally cured and discarded. A mirror (or willing assistant) is helpful to render a smooth outer surface and finished look. DO NOT REMOVE PLUG FROM THE EAR FOR A MINIMUM OF 15 MINUTES. Once cured, gently remove plug by slowly twisting and pulling from top of formed plug. It is recommended the finished ear plug cure an additional three hours before storing in storage bag, however, plug can be used after the 15 minute molding process. A properly formed Ear Plug will have a smooth outer surface, closely contour to the ear and fit snugly.

    Step 6:
  • Repeat for other ear.

    PLEASE READ THE FOLLOWING WARNINGS: Use only as directed. Do not use with latex gloves. Adult supervision required for children. Read and follow all instructions. Do not remove Ear Plug for a minimum of 15 minutes after forming in the ear. Mold material must cure fully before removing from ear. Do not force mold material into ear canal. Do not elongate mold material. Misuse or improperly following instructions may lead to serious injury. Keep out of reach of children. Not responsible for misuse. Do not eat.

  • Not CE Certified..

    • Application Charts & Information

    Overall Rating: 3.71 stars
    Used this Product?Rate It
    5 stars
    John Rohrbaugh of Arlington, TX
    Date posted: 5/25/2008
    Plugs work great! The molding process works exactly as described and as long as you follow the directions the plugs will seal fine.
    Was this review helpful?
    Yes |
    3 found it helpful |
    0 did not
    5 stars
    Tom Rathman of Dunkirk, NY
    Date posted: 6/29/2007
    Easy to follow directions. Makes a very good ear plug.
    Was this review helpful?
    Yes |
    6 found it helpful |
    0 did not
    5 stars
    Ibrahim Samaan of Santa Monica, CA
    Date posted: 5/21/2010
    As a motorcyclist wind noise is loud even with the best full face helmet, these ear plugs are the answer at a very reasonable price, I bought a pair and installed earphone in one of them WOW, I can hear the music at a much lower volume & all day comfort, wind noise is at least 80% less. Great product A*****
    Was this review helpful?
    Yes |
    0 found it helpful |
    0 did not
    4 stars
    Lance Hall of Virginia Beach, VA
    Date posted: 3/2/2010
    Easy to make. You can't wear a stocking hat or wool hat over your ear. The plug will not sit well in your ears. Works good with nothing over the ears.
    Was this review helpful?
    Yes |
    0 found it helpful |
    0 did not
    3 stars
    Richard Zapf of Towson, MD
    Date posted: 7/13/2007
    This product works as advertised. If you like this style of hearing protection, go for it. But I don't find these molded plugs superior to foam plugs.
    Was this review helpful?
    Yes |
    7 found it helpful |
    0 did not
    3 stars
    Michael P of Atlanta, Ga
    Date posted: 8/16/2007
    Ok product but even the slightest variation in the initial molding phase can cause sound/air leaks. No room for error when making the mold. Would not say these are any better than disposable foam.
    Was this review helpful?
    Yes |
    3 found it helpful |
    0 did not
    1 stars
    Chester Wildey of Euless, tx
    Date posted: 8/28/2007
    The plugs were easy to make but unfortunately they didn't block sound well at all. I've seen guys at the range using these, so they must work for some, but for me it was a complete waste of time and money.
    Was this review helpful?
    Yes |
    8 found it helpful |
    0 did not
    Have a question? Visit GunTec Dictionary Need a gunsmith? Visit Gunsmith Locator
    NOTE: Prices, specifications and availability are subject to change without notice.
    We reserve the right to correct typographic, photographic and/or descriptive errors.
    WEBSRVR5